Home › Identifying › How to identify asbestos sheet: clues, limits and the next step

How to identify asbestos sheet: clues, limits and the next step

You cannot identify asbestos sheet by looking at it. You can work out whether a sheet is worth testing, and that takes a few minutes and no tools.

You cannot identify asbestos sheet yourself, and neither can a builder from a photo. Asbestos cement and modern fibre cement look the same, and the fibres are too small to see. What you can do is judge whether a sheet is worth testing.

Most people searching for this are standing in front of a wall, an eave or a fence panel with a job planned. So start with the question that matters: is anyone about to cut, drill or remove it?

If nothing is about to happen, you may not need to know yet

Intact sheet that is sealed, painted and left alone is not an emergency. The risk comes from disturbing it. If you are not renovating, selling or repairing, the sensible answer can be to note where it is and leave it.

Once a drill, a saw or a pressure washer is in the picture, the answer changes. Then you need a result, not a guess.

The clues that make a sheet worth testing

No single clue proves anything. Together they move a sheet from unknown to worth testing.

  • Date of the material. Asbestos was phased out of Australian sheet products through the 1980s, and the total ban took effect on 31 December 2003. Material that predates this is a question.
  • Where it sits. Eaves, wet-area walls, gable ends, fences, sheds and meter box backing boards are common places for old sheet.
  • Thickness. Old sheet is usually a rigid board of about six millimetres, not a thin flexible panel.
  • The back face. Some sheet carries a textured or dimpled reverse. You see it only where a panel is already exposed.
  • Fixings and joints. Closely spaced nails and timber or metal cover strips over the joins are typical of older work.

Our page on what asbestos sheeting looks like goes through these in more detail.

The clues that mislead

Several things feel convincing and are not.

  • Colour. Grey, cream and painted sheet can be either old or new.
  • Chalky weathering. Plenty of modern cement products weather the same way.
  • A stamp or label. A brand name can help you look up what a product was made of, but it is not a result for the sheet in front of you.
  • The age of the house alone. A 1960s house may have new sheet, and a newer extension may reuse old offcuts.

How it gets confirmed

Only a laboratory analysis of a sample confirms it, and the National Association of Testing Authorities (NATA) accreditation is what gives you grounds to rely on the answer. The NSW Government asbestos portal states plainly that you cannot tell by looking.

There are two honest outcomes. You can presume the sheet contains asbestos and handle everything around it on that basis. Or you can have a sample analysed. Which one fits depends on what happens next.

Who takes the sample

Sampling disturbs the material, so it is not a casual job. Whether a householder may take a sample, and what precautions apply, depends on the WHS regulator in your state or territory. A licensed assessor or an accredited laboratory can tell you what is allowed where you live. Check before you pick up a tool.

What to do while you wait

  • Stop work near the sheet.
  • Keep children and pets away from damaged areas.
  • Do not sweep, vacuum or hose broken pieces.
  • Tell any tradesperson you are not sure, so they can plan around it.

If the result is positive, the licence class needed and the amount a householder may handle are set by your state or territory regulator. Those rules differ across Australia, so confirm them before anything is removed.

Frequently asked questions

Can you identify asbestos sheet by looking at it?

No. Asbestos cement and modern fibre cement look alike and the fibres are microscopic. Age, location, thickness and fixings can show a sheet is worth testing, but only laboratory analysis confirms it.

What does asbestos sheet look like?

Typically a rigid grey or painted board about six millimetres thick, often with closely spaced nails and cover strips over the joints. These features suggest testing, not a result.

Does a sheet need testing if I am not touching it?

Not always. Sealed sheet that is intact and left alone can simply be noted. Test or presume asbestos before any cutting, drilling, repair, removal or sale.

Who can test a sheet for asbestos?

A sample is analysed by a laboratory, and NATA accreditation is what makes the result dependable. Who may take the sample is set by the WHS regulator in your state or territory, so check with them first.

Sources

What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.

Keep reading