Home › Identifying › Is Hardiflex asbestos? What the name does and does not tell you

Is Hardiflex asbestos? What the name does and does not tell you

Old Hardiflex sheet was made with asbestos, but later products carried the same name without it. The name is a reason to test, not an answer.

Hardiflex made before the early 1980s was asbestos cement. Hardiflex made later was not. The catch is that the same name stayed on the shelf for decades. So the label alone cannot tell you which one you have.

That is why the honest answer to this question is «possibly, depending on the sheet». Here is how to work out which side yours is likely to sit on.

What the name tells you

Hardiflex was a flat fibre cement sheet sold for walls, ceilings, eaves and wet areas. The Western Australian Department of Health guidance note on identifying asbestos containing material lists Hardiflex among the products that stopped being made with asbestos around 1981. It also warns that the name was used again after 1990 on products that contain no asbestos.

So the same word covers two different materials. If you find it stamped on a sheet, treat it as a strong prompt to find out more. Do not treat it as proof in either direction.

Why the date of the house still matters

A 1981 cut-off sounds clean. It is not, for three reasons.

  • Sales of asbestos building products carried on until about 1987 while manufacturers phased the fibre out.
  • Builders used up backlogged and surplus stock, so a sheet can be younger than the material it is made from.
  • Asbestos was not banned outright in Australia until 31 December 2003.

A house built or renovated in the 1960s or 1970s very likely has asbestos cement sheet somewhere. A house finished in the late 1990s probably does not. The years in between are the grey zone, and that is where a result is worth having.

The marks that help and the ones that do not

  • A readable stamp on the back. Useful if you can see it without disturbing the sheet. It points you to a product to look up, nothing more.
  • Where it sits. Eaves, bathroom walls, laundry linings and fence panels were all common homes for old flat sheet.
  • Thickness and fixings. Rigid board of about six millimetres with closely spaced nails and cover strips suggests older work.
  • Colour or chalkiness. Tells you nothing. New and old sheet weather alike.

You can compare what you see with the photographs in the Asbestos Product Guide. Use it to learn what old products looked like, not to decide what is on your wall.

What to do depending on where the sheet is

Sealed and untouched: note it and leave it. Intact, painted sheet that nobody is cutting or drilling is not a job that needs doing today.

Before any cutting, drilling, sanding or removal: presume it contains asbestos, or have a sample analysed. Do not start work and decide afterwards.

Damaged, cracked or crumbling: stop, keep people away and do not sweep it up. Ask a licensed professional what comes next.

How it actually gets confirmed

Only laboratory analysis of a sample confirms what a sheet is made of. A NATA-accredited laboratory is the one whose result you can rely on. Taking the sample disturbs the material, so check with the WHS regulator in your state or territory about who may do it and what precautions apply.

If you are planning a renovation, get the result before you book trades. It changes the order of the job. Our page on how testing works covers what a result can and cannot tell you.

The short version

Treat Hardiflex in an older house as asbestos until a result says otherwise. Treat it as an open question in a newer one. In both cases, the name is where your checking starts.

Frequently asked questions

Is Hardiflex asbestos?

It depends on when the sheet was made. Hardiflex made before about 1981 was asbestos cement, but the name was reused after 1990 on products without asbestos. Only laboratory analysis of a sample confirms which one you have.

Does the Hardiflex name on a sheet prove it contains asbestos?

No. The name is a strong prompt to find out more, not a result, because it appeared on both older asbestos cement sheet and later non-asbestos products.

Can I drill or cut Hardiflex in an older house?

Not until it is tested or you presume it contains asbestos and follow the rules of your state or territory regulator. Cutting, drilling and sanding release fibres from asbestos cement.

How do I confirm whether my sheet is asbestos?

A sample analysed by a NATA-accredited laboratory. Check with your state or territory WHS regulator about who may take the sample before anyone disturbs the sheet.

Sources

What this page explains is based on these official sources. If you check one and it does not match what you read here, send it to us and the article gets corrected.

Keep reading